Extra Hand Clamp
The Third Hand clamp from the SilvoHome® catalog gives the user the equivalent of an extra hand (figure A). The tool has a flexible hose with clamps on both ends. One clamp attaches to the work surface; the second can hold a work piece or a small ... [... more]
DIYnet |
Shave Horse
A shave horse is a vertical lever and fulcrum used to apply clamping pressure. It's operated by pressing on a toe plate at one end of the lever, forcing the top of the horse to clamp a work piece to its table. Place the lever in the slot, and ... [... more]
DIYnet |
Homemade Clamps
When gluing wood trim to a flat surface, extend the reach of a C-clamp with a short strip of scrap hardwood and a small wood block the same thickness as the trim. Place the block close to the edge of the work piece, then position the strip so it ... [... more]
DIYnet |
The Ultimate Workshop -- The Right Workbench
To build the workbench, major tools you'll need include a table saw for ripping lumber to size and cutting tenons. A circular saw can do in a pinch, but a table saw is preferred. If you use a table saw, you'll need to use one that accepts a dado ... [... more]
DIYnet |
Edge-Gluing Clamps
To use the jig, place two of the wood strips underneath the work pieces, on either side. Place the other two wood strips directly above the bottom strips, on top of the work pieces. Insert carriage bolts and wing nuts through the slots between ... [... more]
DIYnet |
Remodeling And Tools
Speed remodeling time by drilling 1/8" holes in your speed square at 1/4" intervals along the right-angle edge of the square. Run the lipped edge of the square along the board's edge and you'll be able to mark boards as quickly as the pros. You ... [... more]
DIYnet |
Handyman Tool Tip: Clamps
Quick Grip Spreader -- Let's say you need to glue a chair that needs repairing and the legs needs to be spread apart. You can use a normal quick grip to do the job. Simply take one end of the clamp apart, flip it around and slide on the other ... [... more]
DIYnet |
JORGENSEN 3" HOLD DOWN CLAMP
 * Opening capacity of 3", Depth of Throat 1-3/4", Screw diameter 9/16", Load limit, 2,000 lbs
* Malleable and/or ductile iron frames with orange baked enamel finish.
* Scold-drawn steel screws with smoothly cut threads and steel sliding-pin ... [... more]
$18.99
Amazon.com |
Gross Stabil UK 4.5-24 4.5-Inch-24-Inch Heavy Duty ...
* 4 5" Throat Depth
* 24" Nominal Opening
* 1-3/8X7/16" Recessed and notched Steel bar Galvanized spindle and steel bar
* without protective caps
* Molded wooden and painted handle fits comfortably in your hand
Binding : Tools & Hardwar ... [... more]
$39.99
Amazon.com |
Stanley 83-002 6-Inch FatMax Trigger Clamp
* Quickly converts from a clamp to a spreader without the use of tools
* Patent pending drive mechanism provides three times faster travel and 50% more clamping force than competitive products
* Smaller jaw can be positioned anywhere along bar for a range ... [... more]
$14.99
Amazon.com |
IRWIN 226306 6-Inch Heavy Duty Workshop Vise
* 6" Jaw Width
* 8-3/4" Clamping Capacity
* 4-1/4" Throat Depth
*(Irwin-226306-6" Workshop Bench Vise)* - Heavy-duty vises designed for the professional woodworker/metal worker. Swivel base for easy positioning. No. 226304: 4" No. ... [... more]
$124.89
Amazon.com |
Palmgren 18402 410B Milling Vise with Swivel Base 4.0 Inch
* Made in USA
* Vise body length 8-1/2 inch
* Base size 9 inch x 7-1/2 inch
* Center of vise is open for holding work through body of vise
* Vise
Vises are excellent for milling and grinding. Fixed jaw plate has one vertical and one horizontal groove for ... [... more]
$164.99
Amazon.com |
